injection pressure造句
造句與例句
手機版
- Research on lpg free spray at low injection pressure
燃料噴霧過程的研究 - Adjust injection pressure and injection time
調整注塑壓力和注塑時間 - Influence of the injection pressure to plastic mould core offset
注射壓力對塑料模具型芯偏移量的影響 - Bottom - hole injection pressure
井底注水壓力 - Laborotary experiment of water injection pressure decreasing by surfactant
表面活性劑降低注水井注入壓力室內實驗研究 - Raise injection pressure
增加注塑壓力 - Peak injection pressure
峰值噴油壓力 - Air injection pressure
空氣噴射壓力 - 1 . bouble cylinders balanced injection system 2 . multi - steps injection pressure and speed system
二多級壓力，多級速度射膠系統 - The injection pressure of e30 engine corresponding to the lowest fuel consumption is higher than that of diesel engine
E30的最低燃料消耗率對應的噴嘴啟噴壓力略高于柴油。 - It's difficult to see injection pressure in a sentence. 用injection pressure造句挺難的
- Injection pressure should be set low initially and increased to the point of filling the part just short of causing flash
一開始應設定低的射出壓力以填充零件至剛好不會造成毛邊。 - Effects of injection pressure on the microstructures and mechanical properties of short glass fiber injection - moulded reinforced polypropylene
短玻纖增強聚丙烯注射壓力對微觀結構和力學性能影響 - A study of the development model for electronically controlled fuel injection system with high injection pressure for military heavy duty diesel engines
軍用大功率柴油機電控高壓噴油系統的開發方案研究 - It ' s the first time to question extensively the influences of fuel delivery advance angle and injection pressure on performance of e30 engine
首次系統地研究了供油提前角、噴嘴啟噴壓力對e30混合燃料發動機性能的影響。 - The cross - section area of the internal sprue , the fill speed , the fill time and injection pressure are important die casting technology parameters
摘要內澆道截面積、充填速度、充填時間和壓射比壓都是重要的壓鑄工藝參數。 - Process window analysis , another part of mold flow analysis , examines melt temperature , mold temperature , injection pressure , and fill times
加工窗口分析、其它零件的模流分析，檢查熔體溫度、模具溫度、注塑壓力和充填時間。 - Increased needle injection pressure was obsered as the olume of pmma increases and as the distribution of pmma is in close proximity to the cortical walls
同時，使用的聚甲基丙烯酸甲酯黏合劑的體積的增加還可以增大融合椎體的強度。 - Screw bat type pre - plasticized installation , bigger capccity in piasticising , good quality in mixed refine , accuracy in measuring . minimum loss in injection pressure
螺桿式預塑裝置，塑化能力大，混煉質量好，計量準確，注射壓力損失小。 - 3 stages of temperature control , 2 levels of injection pressure , non - stage abjustment injection speed and back pressure , be suitted in precise shaping of engineering plastic
料筒油溫控制，兩極注塑壓力，射速、背壓無段調整，上、下模具溫度獨立控制。 - The research of lpg spray characteristics is done , and the result of calculation shows that the 3mpa injection pressure can satisfy the demand of direct injection
對缸內噴射時lpg的噴霧特性進行了研究，計算結果表明3mpa左右的壓力可滿足lpg缸內噴射的霧化要求。
- 更多造句： 1 2
如何用injection pressure造句，用injection pressure造句，injection pressure in a sentence, 用injection pressure造句和injection pressure的例句由查查漢語詞典提供，版權所有違者必究。